Mô tả sản phẩm
| Product image | Type | Description |
|---|---|---|
 |
LPR-C Thin Pedaling Force Transducer |
Easy mounting applicable different pedal configurations and offset load provide low output errors. |
 |
LSA-A-S1 Gear-change Lever Operating Force Transducer |
Minimal Error due to Different Gripping Applied to a gear-change lever for floor shift, the LSA-A-S1 measures 2-component force generated by operating the gear-change lever. |
 |
LB-B Hand Brake Operating Force Transducer |
The LB-B is a load cell to measure tension of hand brakes. It can be install to a hand brakes easily. Adopting universal joint, the transducer can measure accurately. |
 |
Wheel Torque Transducer |
|
 |
PE-F Engine Pressure Transducer |
The PE-F is a pressure transducer for measurement of burning pressure inside engines. Rated Capacity: 3 MPa Safe Temperature: 300ºC or less for attaching screw section, and 80ºC or less for waste water |
 |
SFA-E-SA20 Steering Force/Angle Transducer |
This unit is thin and lightweight design, easy to mount to and remove from the steering shaft. Strain gages are used to detect steering force (torque) and equipped with strain amplifier. Rotary encoder for steering angle detection is used and enable high resolution. Dedicated indicator is also available for indication of steering force and steering angle. |
 |
SFA-F-SA Steering Force/Angle Transducer |
Easy disconnection from steering shaft This unit is easy to mount to and remove from the steering shaft, and both steering force (torque) and steering angle can be output as strain. *Type that adds output for small angles (rated ±160°) output can also be manufactured. |
 |
SFA-H-SA Steering Force/Angle Transducer |
Lightweight, for easy disconnection General from steering shaft Unit is lightweight, for easy mounting to and removal from the steering shaft |
 |
LSG Grip-Design Steering Force Transducer |
To evaluate the steering operational force from hand to steering wheel |
 |
ASD-B Miniature Crash Test Acceleration Transducer |
The ASD-B is a undamped type compact & lighweight acceleration transducer for crash tests. There are two types vertical models ASD-B-1KH/2KH and horizontal models ASD-B-1KV/2KV. Rated Capacity: ±9807 to ±19613 m/s2 Dimensions: 10 x 4.7 x 12.5 mm Rated Output: 1.2 mV/V or more Frequency Response: DC to 4 kHz, sensitivity deviation: ±5% at 23ºC |
 |
ASDH-A Miniature Crash Test Acceleration Transducer |
The ASDH-A is a undamped type compact & lighweight acceleration transducer with a sputter-type strain gage as the sensing element. There are two types vertical (ASDH-A-1KH/2KH) and horizontal (ASDH-A-1KV/2KV). Rated Capacity: ±9807 to ±19613 m/s2 Dimensions: 10 x 4.7 x 12.5 mm Rated Output: 1.2mV/V or more Frequency Response: DC to 4 kHz, sensitivity deviation ±5% at 23ºC |
 |
ASE-A Damped Acceleration Transducer for Crash Test |
The ASE-A is an oil damped acceleration transducer for crash tests. It is suitable for measuring vibration of car bodies, components, and dummies. Rated Capacity: ±980.7 to ±9807 m/s2 Dimensions: 10 x 5 x 10 mm Rated Output: 0.5 mV/V or more (±980.7 m/s2), 1 mV/V or more (±4903 m/s2), 2 mV/V or more (±9807 m/s2) Frequency Response (23ºC): DC to 1 kHz for all models (Sensitivity deviation ±3%), 1 kHz to 2 kHz for ASE-A-100 (Sensitivity deviation ±10%) (±980.7 m/s2), 1 kHz to 4 kHz for ASE-A-500/1K (Sensitivity deviation ±10%) (±4903 m/s2) |
 |
ASER-A Damped Acceleration Transducer for Crash Test |
The ASER-A is an oil-damped type, suitable for measuring car bodies and dummies. Its cable is exchangeable by repair. Rated Capacity: ±980.7 to ±9807 m/s2 Dimensions: 10 x 5 x 10 mm Rated Output: 0.5 mV/V or more (±980.7 m/s2), 1 mV/V or more (±4903 m/s2), 2 mV/V or more (±9807 m/s2) Frequency Response: (23ºC): DC to 1 kHz for all models (Sensitivity deviation ±3%), 1 kHz to 2 kHz for ASER-A (Sensitivity deviation ±10%) (±980.7 m/s2), DC to 1 kHz for ASER-A-500/1K (Sensitivity deviation ±3%) (±9807 m/s2) |
 |
ASDE-A Damped Acceleration Transducer for Crash Test |
The ASDE-A is an oil-damped type acceleration transducer for crash tests. It is least affected from resonance. Rated Capacity: ±980.7 to ±9807 m/s2 Dimensions: 10 x 4.9 x 13.5 mm Rated Output: 1 mV/V or more Frequency Response: DC to 1 kHz, sensitivity deviation ±3%, 1 kHz to 4 kHz, sensitivity deviation ±10% at 23ºC |
 |
ASDR-A Dumped Accelerometer for Automotive Crash Tests |
The ASDR-A is an oil damped type acceleration transducer for crash tests with exchangeable cable. It is least affected from resonance. Rated Capacity: ±9807 m/s2 Dimensions: 5.4 x 5 x 13 mm Rated Output: 2 mV/V or more Frequency Response: DC to 1 kHz (Sensitivity deviation±3%), 1 k Hz to 4 kHz (Sensitivity deviation ±10% at 23ºC) |
 |
ASM-200BA Miniature Semiconductor Acceleration Transducer |
The ASM-200BA is an undamped type semiconductor acceleration transducer for crash tests. Compact & lightweight ensure minimal influence to the vibration mode of a measuring object. Rated Capacity: 1961 m/s2 Dimensions: 7.6 x 4.6 x 15 mm Rated Output: 1.3 mV/V or more Frequency Response: DC to 3.5 kHz, sensitivity deviation: ±5% at 23ºC |
 |
ASM-1KBCV M3 Miniature Semiconductor Acceleration Transducer |
The ASM-1KBCV M3 is an undamped type semiconductor acceleration transducer for crash tests. Compact & lightweight ensure minimal influence to the vibration mode of a measuring object. The sensitivity direction is perpendicular to the mounting surface. Rated Capacity: ±9807 m/s2 Dimensions: 12 x 5.4 x 25 mm Rated Output: 1.75 mV/V or more Frequency Response: DC to 2.8 kHz, sensitivity deviation: ±5% at 23ºC |
 |
ASM-A-ID Semiconductor Acceleration Transducer for Crash Test |
The ASM-A-ID is a semiconductor acceleration transducer for crash tests. Rated Capacity: ±19614 m/s2 (2000 G) Rated Output: 6 mV/V or more Frequency Response: DC to 2.8 kHz, sensitivity deviation: ±5% at 23ºC |
 |
ASM-1KBCH M3 Miniature Semiconductor Acceleration Transducer |
The ASM-1KBCH M3 is an undamped type semiconductor acceleration transducer for crash tests. Compact & lightweight ensure minimal influence to the vibration mode of a measuring object. The sensitivity direction is parallel to the mounting surface. Rated Capacity: ±9807 m/s2 Dimensions: 12 x 5.4 x 25 mm Rated Output: 1.75 mV/V or more Frequency Response: DC to 2.8 kHz, sensitivity deviation ±5% at 23ºC |
 |
ASM-1KCBV Miniature Semiconductor Acceleration Transducer |
The ASM-1KCB is a undamped type semiconductor acceleration transducer for crash tests. Compact & lightweight ensure minimal influence to the vibration mode of a measuring object. The cable is exchangeable. Rated Capacity: ±9807 m/s2 Dimensions: 16 x 7.7 x 12.5 mm Rated Output: 1.5 mV/V or more Frequency Response: DC to 3.5 kHz, sensitivity deviation: ±5% at 23ºC |
 |
LCF-2TA Femur Load Cell |
For Femur of a Crash Dummy Mounted to the femur of a crash dummy such as Hybrid III, the LCF-2TA detects impact-initiated load to the femur. |
 |
LBT-E Seat Belt Tension Transducer |
Reduced size, weight, and improved nonlinearity Even more compact and lightweight than former models. Additionally, the output correction circuit is built-in, with improved nonlinearity. This has 2 types – left and right depending on the cable direction. Types that support cable replacement using connectors can also be manufactured. |
 |
LBT-A-20KNSA1 Seat Belt Tension Transducer |
Measuring Impact-Initiated Tesion of Seat Belt in Crash Tests Using a strain gage, the LBT-S-20KNS1 detects the impact-initiated tension applied through the dummy to the seat belt. |
 |
LBT-D-100NSA1-H Seat Belt Tension Transducer for CRS |
To use for measuring tensile force to install CRS (Child Restraint Seat) Measure the sensor of seat belt tension. Compact, lightweight and disassembly-friendly design. |
 |
LBT-B-200NSA1-P Seat Belt Tension Transducer for CRS |
Compact, Lightweight, and Easy to Install and Remove Designed to measure the belt tension to fix the child seat, the LBT-B-200NSA1 is compact, lightweight and designed to be easily attached to, or removed from the belt. |
 |
LSM-E-15KNS1 Neck 6-Component Force Transducer |
Neck 6-Component Force Transducer for Dummy Neck Upper Parts Mounted to the neck of a crash dummy such as Hybrid III, the LSM-E-5KNS1 simultaneously detects 6 force components acting to the neck by impactinitiated inertia force generating in the head. |
 |
AMA-A Small-sized Triaxial Accelerometer |
The AMA-A is a compact & lightweight accelerometer with large overloads resistant. Rated Capacity: ±19.61 to ±490.3 m/s2 Dimensions: 10 x 5.8 x 14 mm (±19.61, ±49.03m/s2), 11 × 6.5 × 15 mm (±98.07m/s2), 11 × 11 × 19.3 mm (±490.3m/s2) Rated Output: ±2 V ±0.2 V Frequency Response: DC to 500 Hz (±19.61, ±49.03m/s2), DC to 200 Hz (±98.07, ±490.3m/s2) Safe Overloads: ±19613 m/s2 (±19.61, ±49.03m/s2), ±9807 m/s2 (±98.07, ±490.3m/s2) |
 |
ASPA-A Piezoelectric Acceleration Transducer (Built-in Amplifier) |
The ASPA-A is a piezoelectric acceleration transducer with built-in amplifier for measuring high range from slight to large acceleration in high sensitivity. Applicable acceleration: ±2200m/s2 Dimensions: φ7.8 x 15.7 x Hex7 mm Voltage Sensitivity: 1.0 mV per m/s2 ±10% Power Supply: 15 to 25 VDC, 0.5 to 5.0 mA |
 |
ASPB-A Piezoelectric Acceleration Transducer (Built-in Amplifier) |
The ASPB-A is a piezoelectric acceleration transducer with built-in amplifier for measuring high range from slight to large acceleration in high sensitivity. Applicable acceleration: ±2200 m/s2 Dimensions: φ8.5 x 11.5 x Hex9 mm Voltage Sensitivity: 1.0 mV per m/s2 ±10% Power Supply: 15 to 25 VDC, 0.5 to 5.0 mA |
 |
ASPC-A Piezoelectric Acceleration Transducer (Built-in Amplifier) |
The ASPC-A is a piezoelectric acceleration transducer with built-in amplifier for measuring high range from slight to large acceleration in high sensitivity. Applicable acceleration: ±400 to ±3600 m/s2 Dimensions: 14.2 x 14.2 x 23.7 mm Voltage Sensitivity: 1.0 to 10 mV per m/s2 ±10% Power Supply: 21to 24 VDC, 0.5 to 10 mA |
 |
DLT-AS Inductance-type Displacement Transducer |
The DLT-AS is an inductance-type displacement transducer with less friction and small measuring force. Rated Capacity: ±5 to ±500 mm Nonlinearity: Within ±0.5% RO Rated Output: Approx. 2 mV/V |
 |
DLT-BS Inductance-type Displacement Transducer |
The DLT-BS is a water-proof displacement transducer. Rated Capacity: ±5 to ±500 mm Nonlinearity: Within ±0.5%RO Rated Output: Approx. 2 mV/V |
 |
DT-D Dial Gage-equipped Displacement Transducer |
The DT-D is a displacement transducer equiped with dial enables to visual measured displacement. Rated Capacity: 10, 20, 30, 50 mm Nonlinearity: Within ±0.5% RO Measuring Force: Approx. 1.7 N (10 mm), approx. 2.1 N (20 mm), approx. 2.2 N (30 mm), approx. 2.7 N (50mm) Rated Output: 1.5 mV/V or more |
 |
DTH-A Displacement Transducer |
The DTH-A is a high accuracy, compact & lightweight displacement transducer. Rated Capacity: 5 to 100 mm Nonlinearity: Within ±0.1% RO Measuring Force: Approx. 1.5 to 4 N Rated Output: 5 mV/V ±0.1%, ±0.15% (5 mm) |
 |
DTK-A Displacement Transducer |
The DTK-A is a small-sized displacement transducer for both tension and compresion measurement. A measuring scale provided. Rated Capacity: 30, 50 mm Nonlinearity: Within ±0.3% RO Measuring Force: Approx. 2 N Rated Output: 2.5 mV/V or more The transducer can be measured in two-way tension and compression. |
 |
DTP-D-S Potentiometer-type Displacement Transducer |
The DTP-D is a potentiometer-type displacement transducer. It converts expansion or contraction of a sensing wire to electric signal by a built-in potentiometer. Rated Capacity: 2000, 5000 mm Nonlinearity: Within ±0.3% RO Measuring Force: Approx. 0.59 N (2000 mm), approx. 1.7 N (5000 mm) (Pull-out Direction) Rated Output: 5 mV/V±0.3% |
 |
GSAT-A Three Axis Angular Rate Gyro |
The GSAT-A is a compact & lighweight angular rate gyro for measurig anglar rate of 3 axes. Rated Capacity: ±900 deg/s (±15.708 rad/s) Dimensions: 10 x 8 x 20 mm Rated Output: Approx. ±2 V/V Recommended Excitation: DC ±2.5 to 5.0 V with dual supply Safe Shock Resistant: 9807 m/s2 |
 |
LC-V Small-sized Compression Load Cell |
The LC-V is a compact & lightweight load cell for measuring compressive loads. It is easy installation into existing facilities. The Steady Brace ensures to cancel transverse loads resulted from horizontal displacement. Rated Capacity: 50 kN to 200 kN Diameter: 68 mm (50 kN), 78 mm (100 kN), 98 mm (200 kN) Nonlinearity: Within ±0.05% RO |
 |
LCH-F High-accuracy Compression Load Cell |
The LCH-F is a high accuracy load cell. It is the highest measuring accuracy in high humidity place. Rated Capacity: 100 kN, 200 kN Diameter: 156 mm (100 kN), 176 mm (200 kN) Nonlinearity: Within ±0.02% RO |
 |
LCK-A Thin Compression Load Cell |
The LCK-A is a compressive load cell with excellent accuracy, reliability, stability, and response. They also have a thin design for convenient installation as detection terminals of weighing systems. Rated Capacity: 5 kN to 200 kN Diameter: 78 mm (5 kN to 20 kN), 98 mm (50 kN), 108 mm (100 kN), 118 mm (200 kN) Nonlinearity: Within ±0.2% RO for 5 kN to 100 kN, within ±0.5% RO for 200 kN |
 |
LCN-A Small-sized Compression Load Cell |
The LCN-A is a stainless-steel load cell, for measuring compressive loads. It is compact & lightweight. Excellent stability and reliability are ensured by the hermetically-sealed structure with inert gas filled in. Rated Capacity: 500 N to 20 kN Diameter: 50 mm Nonlinearity: Within ±0.15% RO |
 |
LCR-G-SA2 Small-sized Large-capacity Compression Load Cell |
The LCR-G-SA2 is a compact & lightweight load cell for measuring compressive loads. Rated Capacity: 10 to 50 kN Diameter: 20 mm (10 to 30 kN), 25 mm (50 kN) Nonlinearity: Within ±1% RO Others: Since the cable comes from the bottom, the load cells can be inserted into cylindrical objects for measurement. |
 |
LCX-A-ID Small-sized Compression Load Cell |
The LCX-A-ID is a stainless-steel load cell, for measuring compressive loads. It is compact & lightweight. Rated Capacity: 500 N to 20 kN Diameter: 28 mm (500 N to 2 kN), 43 mm (5 kN to 20 kN) Nonlinearity: Within ±0.1% RO |
 |
LFM-A Compact 6-component Force Transducer |
The LFM-A is a 6-component force transducer. It enables simultaneous measurement of 3 components of force (Fx, Fy, Fz) in 3 axial directions and 3 moments (Mx, My, Mz) around the axes. Rated Capacity: 1 kN, 3 kN Diameter: 66 mm Nonlinearity: Within ±0.5% RO |
 |
LFX-A Compact 6-component Force Transducer with Built-in Amplifier |
The LFX-A is a 6-component force transducer with built-in Amplifiers. It enables simultaneous measurement of 3 components of force (Fx, Fy, Fz) in 3 axial directions and 3 moments (Mx, My, Mz) around the axes. Hollowed structure for wiring easily. Rated Capacity: 1 kN, 3 kN Diameter: 66 mm Nonlinearity: Within ±0.5% RO |
 |
LMA-A Small-sized Compression Load Cell |
The LMA-A is a compact & lightweight load cell for measuring compressive loads. Rated Capacity: 5 N to 1 kN Diameter: 12 mm (5 to 50 N), 20 mm (100 N to 1 kN) Nonlinearity: Within ±1% RO |
 |
LMB-A Small-sized Compression Load Cell |
The LMB-A is an utra-small load cell for measuring compressive loads. Rated Capacity: 10 N to 2 kN Diameter: 10 mm (10 to 200 N), 16 mm (500 N to 2 kN) Nonlinearity: Within ±0.5% RO |
 |
LMBT-A Small-sized Compression Load Cell |
The LMBT-A is an ultra-small load cell for measuring compressive loads. Its operating temperature is up to 100ºC. Rated Capacity: 50 N to 2 kN Diameter: 10 mm (50 to 200 N), 16 mm (500 N to 2 kN) Nonlinearity: Within ±0.3% RO |
 |
LMC-A Small-sized Compression Load Cell |
The LMC-A is a compact & lightweight load cell for measuring compressive loads. Rated Capacity: 5 kN to 50 kN Diameter: 12±0.1mm （5, 10 kN), 16±0.1mm (20 kN), 22±0.2mm (50 kN) Nonlinearity: Within ±0.5% RO for 5 kN to 10 kN, within ±1% RO for 20 kN to 50 kN |
 |
LMR-S-SA2 Small-sized Compression Load Cell |
The LMR-S-SA2 is a compact & lightweight load cell for measuring compressive loads. Rated Capacity: 2 kN to 20 kN Diameter: 21 mm Nonlinearity: Within ±1% RO, within ±2% RO for 20 kN |
 |
LSM-B-SA1 3-component Force Transducer |
The LSM-B-SA1 is a strain gage based 3-component force transducer for simultaneously measuring force in 3 directions of X, Y, and Z. Rated Capacity: 10 to 500 N Diameter: 88 mm Nonlinearity: Within ±0.5% RO |
 |
LU-E Tension/Compression Load Cell |
The LU-E is a load cell for measuring tension or compression loads. It is hermetically-seal structure with inert gas filled in. Rated Capacity: ±500 N to ±200 kN Diameter: 80 mm (±500 N to ±2 kN), 100 mm (±5 kN to ±20 kN), 112 mm (±50 kN), 138 mm (±100 kN), 186 mm (±200 kN) Nonlinearity: Within ±0.2% RO |
 |
LUH-F High-accuracy Tension/Compression Load Cell |
The LUH-F is a load cell for measuring tension or compression loads. It is hermetically-seal structure with inert gas filled in and excellent in zero float characteristics. Rated Capacity: ±500 N to ±200 kN Diameter: 100 mm (±500 N to ±5 kN), 100 mm (±10 kN to ±20 kN), 130 mm (±50 kN), 160 mm (±100 kN), 200 mm (±200 kN) Nonlinearity: Within ±0.02% RO |
 |
LUK-A Tension/Compression Load Cell |
The LUK-A is a a thin load cell for measuring tension or compression loads. It can be installed to where the height is limited. It also suitable for fatigue test where repeativite loads are applied continuously. Rated Capacity: ±5 kN to ±2 MN Diameter: 77 mm (±5 kN to ±10 kN), 107 mm (±20 kN), 127 mm (±50 kN), 157 mm (±100 kN), 227 mm (±200 kN), 307 mm (±500 kN), 375 mm (±1 MN), 560 mm (±2 MN) Nonlinearity: Within ±0.1% RO for 5 kN to 200 kN, within ±0.2% RO for 500 kN to 2 MN |
 |
LUR-A-SA1 Compact Tension/Compression Load Cell |
The LUR-A-SA1 is a load cell for measuring tension or compression loads. Rated Capacity: ±50 N to ±2 kN Diameter: 28 mm Nonlinearity: Within ±0.5% RO |
 |
LUR-B-SA1 Jack Load Cell |
The LUR-B-SA1 is load cell for measuring loads applied to jacks. Rated Capacity: ±10 kN to ±2 MN Diameter: 100 mm (±10 kN), 110 mm (±20 kN), 125 mm (±30 kN, ±50 kN), 175 mm (±100 kN), 255 mm (±200 kN, ±300 kN), 330 mm (±500 kN), 430 mm (±1 MN), 530 mm (±1.5 MN), 590 mm (±2 MN) Nonlinearity: Within ±0.2% RO for 10 kN to 200 kN, within ±0.5% RO for 300 kN to 2 MN |
 |
LUX-B-ID Compact Tension/Compression Load Cell |
The LUX-B-ID is a compact stainless-steel load cell with waterproof connector for measuring tension or compression loads. Models for withstand to repeated bending (Flexible cable) are available. Rated Capacity: ±50 N to ±20 kN Diameter: 43 mm Nonlinearity: Within ±0.1% RO for 5 kN to 20 kN, within ±0.15% RO for 50 N to 2 kN |
 |
PG-H High Pressure Transducer |
The PG-H is a high pressure transducer with hermetically sealed with inert gas filled in. It is suitable for high pressure measurement. Rated Capacity: 100, 200 MPa Compensated Temperature: -10 to 70ºC |
 |
PG-U Pressure Transducer |
The PG-U is a pressure transducer with high accuracy and reliability because of hermetically-sealed structure with inert gas filled in. Rated Capacity: 200 kPa to 50 MPa Compensated Temperature: -10 to 60ºC |
 |
PGL-A Small-sized Pressure Transducer |
The PGL-A is a compact & lightweight pressure transducer with the semi-flush diaphragm at the end. It is high accuracy. Rated Capacity: 1 to 50 MPa Compensated Temperature: -10 to 60ºC |
 |
PGM-D Small-sized Pressure Transducer |
The PGM-D is a small-sized pressure transducer with the diaphragm at the end. Rated Capacity: 5 to 50 MPa Compensated Temperature: 0 to 60ºC |
 |
PGM-E Small-sized Pressure Transducer |
The PGM-E is a small-sized pressure transducer with the semi-flush diaphragm at the end. Rated Capacity: 1 to 50 MPa Compensated Temperature: -10 to 60ºC |
 |
PGM-H Small-sized Pressure Transducer |
The PGM-H is a small-sized pressure transducer with the semi-flush diaphragm at the end. Rated Capacity: 500 kPa to 50 MPa Compensated Temperature: -10 to 60ºC |
 |
PGMC-A Small-sized Pressure Transducer |
The PGMC-A is a compact pressure transducer with flush-diaphragm at the end. Rated Capacity: 200 kPa to 1 MPa Compensated Temperature: 0 to 50ºC |
 |
PGS-A Small-sized Pressure Transducer |
The PGS-A is a compact & lightweight pressure transducer that has high vibration & impact resistant. Rated Capacity: 1 to 50 MPa Compensated Temperature: -10 to 60ºC |
 |
PHB-A High/Low-temperature Pressure Transducer |
The PHB-A is a pressure transducer for measuring pressure at high or low temperatures. The sensing surface is a stainless steel diaphragm. Rated Capacity: 1 to 50 MPa Compensated Temperature: -196 to 200ºC |
 |
PHC-B Flush Diaphragm Type High-temperature Pressure Transducer |
The PHC-B is a flush-diaphragm type pressure transducer for measuring pressure at high temperature. It adopt thin-film strain gage formed by sputtering. Rated Capacity: 2 to 20 MPa Compensated Temperature: 23 to 230ºC |
 |
PHF-S-SA2 Small-sized High-temperature Pressure Transducer |
The PHF-S-SA2 is a compact & lightweight pressure transducer for measuring pressure at high temperature up to 150ºC. Rated Capacity: 2 to 20 MPa Compensated Temperature: -40 to 150ºC |
 |
PHF-S-SA4 Small-sized High-temperature Pressure Transducer |
The PHF-S-SA4 is a compact & lightweight pressure transducer for measuring pressure at high temperature up to 150ºC. Rated Capacity: 2 to 10 MPa Compensated Temperature: -40 to 150ºC |
 |
PHF-S-S1 Compact High-temperature Pressure Transducer |
The PHF-S-S1is a high-temperature pressure transducer that easy to wire or exchange cable. UNF and G type screws are available from size 8 to 12 mm. Rated Capacity: 2 to 20 MPa Compensated Temperature: -40 to 150ºC |
 |
PHL-A Small-sized High/Low-temperature Pressure Transducer |
The PHL-A is a compact & lightweight pressure transducer with the semi-flush diaphragm at the end. It is suitable for measurement under high or low temperature. Rated Capacity: 1 to 50 MPa Compensated Temperature: -20 to 150ºC for PHL-A-A, -196 to 200ºC for PHL-A-B |
 |
PS-C Miniature Pressure Sensor |
The PS-C is a miniature pressure sensor with a strain-gage bridge inside. The cable direction is parallel to the sensor surface. Rated Capacity: 50 kPa to 7 MPa Compensated Temperature: 0 to 50ºC |
 |
PS-D Miniature Pressure Sensor |
The PS-D is a miniature pressure sensor with a strain-gage bridge inside. The cable direction is at right angle to the sensor surface. Rated Capacity: 50 kPa to 7 MPa Compensated Temperature: 0 to 50ºC |
 |
PSS Miniature Pressure Sensor |
The PSS is a miniature pressure sensor with a strain-gage bridge inside. Thin-film strain gages are directly formed on the diaphragm. Rated Capacity: 20, 50, 100 kPa Compensated Temperature: 0 to 50ºC (As for PSS-AF/BF, Non-condensing) |
 |
TPH-A Highly Rigid Torque Transducer |
The TPH-A is a noncontact highly rigid torque transducer with high frequency response and high accuracy. Rated Capacity: ±500 N･m to ±50 kN･m Rated Output: ±10 V, 4 to 20 mA Max. Rotation Speed: 10000 rpm for ±500 N･m, 5000 rpm for ±10 kN･m, and 3000 rpm for ±20 to 50 kN･m |
 |
TPS-A Built-in Amplifier Torque Transducer |
The TPS-A is a compact & lightweight torque transducer with buit-in amplifier. Easy maitenance due to noncontact transmission. Rated Capacity: ±0.1 N･m to ±5 kN･m Rated Output: ± (5+0.2) V at load resistance 5 kΩ or more, 2 kΩ or more for ±0.11 N･m to ±2 N･m Max. Rotation Speed: 15000 rpm for ± 0.1 N・m to ±2 N・m, 5000 rpm for ±5 N･m to ±500 N･m, 4000 rpm for ±1 kN･m, and 3000 rpm for ±5 kN･m |
 |
LBR-S Hand Brake Operating Force Transducer |
The LBR-S is a load cell to measure tension of parking brakes. It can be install to a parking brakes easily. Thetransducer can measure vertical force applied to the parking brake accurately. |
Tags: Automotive transducers, Kyowa
